Kontron NSW1U IP Network Server Instrukcja Użytkownika Strona 73
- Strona / 110
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Kontron IP Network Server NSW1U
December 2009 Product Guide, rev. 1.4
73
Server Component Replacements—NSW1U Network Server
6. If this is the last task you are performing, replace the riser card assembly, the processor air duct,
and the top cover of the chassis. Reconnect all the external devices and plug in the power cord(s).
5.5 Replacing the Server Board
The Kontron IP Network Server NSW1U uses the Intel
®
S5000PHB server board. To replace the server
board, the following components must be removed before removing the board from the chassis:
• Cable connections on the server board
• Processor air duct
• PCI riser card assembly
• Remote Management Module 2, if installed
In addition, once the server board is removed from the chassis, the following components should be
removed so they can be reused on the new server board if it hasn’t already been configured:
•Heat sink
• Processor
• All DIMMs
• Battery
To replace the server board, use the following instructions.
Caution: Before replacing any components inside the server, you must first take the server out
of service, turn off all peripheral devices connected to the system, turn off the system
by pressing the power button, and unplug the power cord(s) from the system or wall
outlet.
5.5.1 Removing the Server Board
1. Power down the server system and unplug all peripheral devices and the power cable.
2. Remove the chassis cover. For instructions, see Section 3.2.1, “Removing the Chassis Cover” on
page 25.
3. Remove the PCI riser assembly. For instructions, see Section 4.2.2, “Installing a Drive into the
Drive Tray” on page 47
4. Remove the processor air duct. For instructions, see Section 3.2.5, “Removing the Processor Air
Duct” on page 27.
5. Remove the power distribution board. For instructions, see Section 5.4.1, “Removing the Power
Distribution Board” on page 71.
6. Remove the Intel
®
Remote Management Module 2 if installed. For information, see Section 4.5.2,
“Installing the RMM2” on page 55.
7. Disconnect any cables from the server board.
8. Remove the seven screws that attach the server board to the chassis. (“A”)
9. Tilt the server board and lift it from the chassis. Use caution in pulling it out from beneath the rear
panel.
- Product Guide 1
- Rev. 1.4 1
- Contents 3
- NSW1U Network Server—Contents 4
- Contents—NSW1U Network Server 5
- Revision History 7
- 1 Introduction 9
- 1.3 Product Accessories 10
- •System drivers 11
- • Firmware and BIOS updates 11
- 2.1 Server Components 14
- 2.2 Back Panel 15
- 2.3 NSW1U Server Front Panels 16
- AF000816rev3 17
- AF000817rev 18
- AF000818 19
- 2.5.1 Front Panel Features 20
- AF000750 21
- 2.8 Hard Disk Drives 22
- 2.9 Riser Card Assembly 22
- 2.10 Power Supply 22
- 2.11 System Cooling 22
- AF000830 23
- 2.12 Hardware Requirements 24
- 3.1 Before You Begin 25
- AF000876rev 26
- AF000875 27
- AF000880 28
- 3.3.1.1 Jumper Blocks 29
- 3.3.1.4 BIOS Select Jumper 30
- DIMM Sockets 32
- 3.3.3.1 Installing DIMMs 34
- AF000775 35
- 19, “A” and “B”) 37
- AF000769 38
- AF000770 38
- AF000773 39
- AF000877 41
- 4.1 Before You Begin 45
- AF000820 48
- TS000407 49
- TS000409 50
- TS000410 51
- TS000411 52
- TS000213 53
- TS000214 54
- 4.5.2 Installing the RMM2 55
- GCM3 ModuleRMM Module 56
- AF000884 57
- AF000887 58
- AF000888 59
- AF000886 60
- TS000504 61
- TS000505 62
- TS000506 62
- TS000507 63
- TS000508 64
- 5.1 Before You Begin 65
- TS000404 66
- TS000405 67
- TS000406 68
- AF000896 69
- AF000897 71
- AF000894 72
- AF000895 72
- AF000898 74
- AF000899 75
- TS000416 77
- TS000417 78
- 5.6.2 Running Setup 79
- 6 Server Utilities 80
- 6.2 Updating the BIOS 81
- Yes] [NO] 81
- 6.2.1.2 Obtaining the Update 82
- 6.3 Clearing the CMOS 82
- 6.4 Clearing the Password 83
- 7 Troubleshooting 84
- 7.5 LED Information 89
- 7.6 BIOS Error Messages 90
- 7.6.1 BIOS POST Beep Codes 91
- Table 11. BMC Beep Codes 92
- 8 Warranty 93
- A.1 Emissions Disclaimer 94
- A.2 Intended Uses 94
- A.3 Safety Cautions 96
- Wichtige Sicherheitshinweise 97
- Consignes de sécurité 99
- B.2.1 FCC (USA) 106
- B.2.4 VCCI (Japan) 107
- B.2.5 BSMI (Taiwan) 107
- B.2.6 Korean RRL Compliance 108
- Appendix C: Getting Help 109
Powiązane produkty i podręczniki dla Sprzęt komputerowy Kontron NSW1U IP Network Server
(9 strony)
(49 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji